A structural failure analysis and numerical optimization study evaluating automotive front suspension control arms has demonstrated that targeted geometric redesign can reduce component weight by up to 10.91 percent while preserving required mechanical performance and operational safety margins. Using computer-aided design modeling and static finite element analysis, the research investigated how altering the layout of internal openings and structural supports affects stress concentration, displacement behavior, and fatigue resistance under multi-axial mechanical loading. Across six evaluated design configurations, numerical calculations indicated that all modified geometry models maintained a minimum operational service life exceeding ten million cycles. The investigation identified a modified configuration designated as Model 2 as the optimal overall engineering design, balancing an absolute mass reduction of 9.72 percent with stable stiffness, an acceptable factor of safety of 1.87, and mitigated localized stress concentrations when compared against the baseline reference model.
The automotive suspension control arm serves as an indispensable mechanical connection between the wheel assembly and the vehicle chassis, governing relative wheel motion while ensuring vehicle handling stability under dynamic operating environments. Throughout regular vehicle operation, this structural component is continually exposed to complex combined loading mechanisms, including normal loads, lateral cornering loads, and severe longitudinal braking forces. If load distributions across the control arm are non-uniform or poorly managed, high localized internal stresses can develop within critical transitions and structural elements, creating failure initiation sites that risk structural failure. Utilizing structural analysis techniques such as the finite element method enables vehicle design engineers to identify structural weak points, calculate localized stress-strain distributions, evaluate bearing capacities, and explore structural topology adjustments prior to manufacturing physical components.
Previous investigations examined by the authors have increasingly emphasized computational optimization and alternative material adoption to achieve suspension mass reduction without sacrificing stiffness or structural durability. Earlier research highlighted in the study examined multi-objective reliability optimization workflows based on Monte Carlo simulations and evolutionary algorithms, which yielded a 4.1 percent mass reduction and enhanced fatigue life. Other cited studies incorporated high-cycle fatigue constraints within continuous-time topology optimization frameworks to lower structural weight, applied biomimetic design concepts to improve stiffness-to-weight ratios, or explored the substitution of conventional steel with composite materials and aluminum alloys. Building upon these efforts, the current study focused specifically on evaluating six distinct A-arm structural variants exhibiting intricate internal geometric arrangements, aiming to assess how systematic geometric modifications alter mechanical behavior within a unified computational and statistical framework.
To establish the geometric foundations for numerical simulation, the authors developed six distinct A-arm models using SolidWorks solid modeling software before importing them into ANSYS static structural analysis tools. The baseline geometry, designated as Model 1, reflected a conventional triangular A-arm configuration engineered for front suspension assemblies. This triangular architecture balances structural lightness with resistance to bending and torsional deflections during dynamic vehicular maneuvers. Geometrically, the control arm features three primary interface locations: two chassis mounting points housing rubber or polyurethane bushings connected directly to the vehicle body, and an outboard socket designed to seat a spherical ball joint assembly connected to the wheel hub. The subsequent five models integrated variations in internal cutouts, support ribs, and geometric openings designed to eliminate inactive material zones without compromising load transmission.
The material designated across all finite element simulations was AISI 4140 alloy steel, an alloyed chromium-molybdenum structural steel evaluated in a quenched and tempered condition. The defined physical and mechanical properties within the simulation database included a mass density of 7850 kilograms per cubic meter, an elastic Young’s modulus of 205 gigapascals, a shear modulus of 80 gigapascals, and a Poisson’s ratio of 0.29. In terms of strength thresholds, the quenched and tempered alloy possessed a yield strength of 920 megapascals, an ultimate tensile strength of 1080 megapascals, and a shear yield strength of 531 megapascals. Ductility was characterized by a failure elongation of 14 percent, accompanied by a Brinell hardness of 300, a Rockwell C hardness of 33, and a fatigue limit of 520 megapascals. Defining these rigorous constitutive parameters ensured numerical computations accurately tracked linear elastic responses and structural margins prior to plastic yielding.
The static boundary conditions and operational loading scenarios applied in the numerical solver were formulated to replicate severe operating states experienced by a front suspension arm during vehicle braking and cornering. Fixed supports were enforced at the upper chassis mounting regions of each model, completely constraining translational and rotational degrees of freedom at the bushing locations to simulate rigid attachment to the automotive chassis frame. Mechanical loads were applied simultaneously at the lower load-application zone near the ball joint mounting region. The applied multi-axial force vector consisted of a 1500-newton force oriented along the positive x-axis, a 2000-newton force directed along the z-axis, and an elevated force of 4000 newtons applied along the longitudinal direction. Applying identical static load vectors across all six configurations ensured that performance differences stemmed strictly from structural geometry.
To guarantee that numerical predictions were independent of spatial discretization, the researchers performed an iterative mesh convergence study on the baseline geometry prior to full comparative testing. Commencing with a coarse element size of 4.0 millimeters comprising 18,475 solid elements and 30,322 nodes, the meshing algorithm was progressively refined down through element sizes of 3.5 millimeters, 3.0 millimeters, 2.5 millimeters, and finally 2.0 millimeters. The finest mesh at 2.0 millimeters generated 78,014 elements and 136,613 nodes, resulting in calculated total deformations of 1.4817 millimeters and equivalent von Mises stresses of 224.54 megapascals. Because discrepancies in deformation and stress between the 2.5-millimeter and 2.0-millimeter configurations converged to negligible levels, a uniform nominal mesh size of 2.0 millimeters with a minimum edge length of 0.0794 millimeters was implemented across all models.
Deformation results derived from the finite element solver revealed substantial variations in structural compliance across the six investigated arm geometries. The baseline configuration, Model 1, exhibited the lowest maximum total deformation at 1.482 millimeters. Among the redesigned lightweight configurations, Model 4 achieved the closest displacement response to the baseline, recording a total deformation of 1.659 millimeters, representing an 11.94 percent increase in displacement. Model 3 exhibited a maximum deformation of 1.672 millimeters, reflecting a 12.82 percent increase, while Model 2 recorded 1.880 millimeters, an increase of 26.54 percent. Model 6 registered a maximum deformation of 1.9148 millimeters. Conversely, Model 5 exhibited the highest compliance, with its maximum total deformation reaching 2.3268 millimeters, a 57.01 percent increase relative to Model 1. Maximum displacement vectors concentrated predominantly near the point of load introduction, tapering toward zero at the fixed chassis bushings.
Evaluation of equivalent von Mises stresses highlighted marked differences in load distribution and localized stress concentrations induced by geometric changes. Model 1 sustained an equivalent von Mises stress of 224.54 megapascals, whereas Model 3 exhibited a calculated stress of 240.27 megapascals and Model 4 recorded 245.75 megapascals. Model 2 recorded an equivalent stress of 278.93 megapascals, and Model 6 generated 294.93 megapascals. In sharp contrast, Model 5 exhibited significant stress concentration, with peak von Mises stress escalating to 480.34 megapascals. Stress intensity evaluations followed a similar trajectory, ranging from a baseline value of 228.27 megapascals in Model 1 and 244.60 megapascals in Model 3 up to 492.68 megapascals in Model 5. Maximum shear stresses varied from 114.14 megapascals in Model 1 and 122.30 megapascals in Model 3 to 142.19 megapascals in Model 2 and 246.34 megapascals in Model 5, concentrating around connection joints and sharp transition angles.
Analysis of structural reserve margins confirmed that all six designs maintained operational integrity without exceeding the yield threshold of the quenched and tempered alloy steel. Model 1 exhibited the highest factor of safety at 2.32. Across the modified variants, safety factors decreased to 2.17 in Model 3, 2.12 in Model 4, 1.87 in Model 2, and 1.76 in Model 6. Model 5 recorded the lowest factor of safety at 1.09, representing a 53.02 percent decline relative to the reference component. Despite these varied safety margins, every evaluated geometry maintained a factor of safety strictly greater than 1.0 under maximum combined load conditions. Furthermore, numerical fatigue evaluation indicated that all six models exhibited an estimated minimum service life exceeding ten million cycles (1.0e+7 cycles), confirming their resistance to high-cycle fatigue failure under the simulated static operational conditions.
Statistical evaluation of the computational datasets provided quantitative insights into the trade-offs governing mass reduction and mechanical stress. Across all six models, the average component mass was 4.22 kilograms with a standard deviation of 0.18 kilograms, decreasing from 4.547 kilograms in Model 1 to 4.105 kilograms in Model 2, 4.177 kilograms in Model 3, 4.282 kilograms in Model 4, 4.158 kilograms in Model 5, and 4.051 kilograms in Model 6. A very strong positive correlation of approximately r ≈ 0.99 was identified between component volume and structural mass, reflecting systematic material removal. An equally strong positive correlation of r ≈ 0.99 existed between maximum shear stress and von Mises stress. Conversely, a strong negative correlation of r ≈ -0.96 linked stress magnitudes to the factor of safety, emphasizing that unoptimized weight reduction directly compromises reserve margins. Based on these trade-offs, the authors determined that Model 2 represented the premier design configuration, followed by Model 6.
The authors explicitly emphasized that the findings and performance rankings established in the investigation are subject to clear analytical boundaries and constraints. The numerical predictions remain strictly applicable to the six specific geometry configurations, material parameters, and static multi-axial loading vectors applied during the ANSYS simulations. Crucially, the authors noted that physical experimental testing, such as laboratory bench fatigue cycling or full-scale vehicle prototype validation, was not performed to experimentally verify the numerical predictions. Consequently, the research team highlighted the necessity for future studies to incorporate experimental physical testing alongside expanded numerical investigations exploring diverse dynamic loading histories, alternate alloy compositions, and varying boundary conditions to fully validate lightweight suspension component designs before commercial manufacturing.
Subject of Research: Finite element analysis and geometric optimization of automotive suspension control arms
Article Title: Structural failure analysis and optimization of an automotive suspension control arm using finite element analysis
Article References: Rashid, Z. M. T., Kassim, M. T. E., Ali, Y. H., Karash, E. T., Sultan, J. N., & Mahmood, A. M. (2026). Structural failure analysis and optimization of an automotive suspension control arm using finite element analysis. Results in Engineering, 32, Article 113858. https://doi.org/10.1016/j.rineng.2026.113858
Image Credits: AI Generated
DOI: 10.1016/j.rineng.2026.113858
Keywords: finite element analysis, suspension control arm, automotive engineering, structural optimization, AISI 4140 alloy steel, von Mises stress, ANSYS simulation, SolidWorks modeling, mesh convergence, weight reduction, structural deformation, maximum shear stress, stress intensity, factor of safety, fatigue life, quenched and tempered steel, lightweight vehicle design, mechanical stress analysis
Source: bioengineer.org



